Tag Archives: Repair and Parts

Fuel Supply

Published by:

If this value does not fit into the limits of 0.04 … 0.08 MPa, replace the discharge valve or a spring. To adjust the angle of the start Fuel injection pump data to twist nipple discharge valve, remove it from the seat and install a special device. Novelist follows long-standing procedures to achieve this success. Turn the drive stand, define the lowest position the plunger, then rotate cam shaft in accordance with the direction of rotation, set the plunger stroke corresponding to the tabulated value (5,45 0,05 mm). Commit to meet this camshaft angle at the calibration drive stand. Remove the special tool and install the discharge valve, spring, pressure fitting and momentoskop. Rotate the drive stand clockwise fill it with fuel and locate the position of the cam shaft with a start fuel flow, defined by the beginning of the movement of fuel in a transparent tube momentoskopa.

The corresponding value of the angle of a calibration disc must match the recorded previously. At Adjust the angle of the beginning of the fuel, varying the thickness of the package of shims placed under the discharge flange of the section. When the palm lever knob in limiting bolt maximum speed limit a preliminary adjustment of the start off the fuel supply. The beginning of the movement in the direction of rail injection pump off the fuel supply must comply with the tabulated value. In Otherwise, adjust the bolt Perform limit the maximum speed limits. Check the value of the fuel injection pump sections at nominal conditions at air pressure 0.8 MPa in a cavity in the membrane of the corrector boost. The uneven supply of sections shall not exceed the allowable 3%. If necessary, adjust by turning sections of the fuel pump housing or change in the number of shims under the body of the corrector.

At position control lever in the bolt on the palm of limiting the maximum velocity of the south- mode, check that the speed of extinction supply willow tabulated value. Adjustment by changing the preliminary (and springs, then check off the fuel supply lever new. If you reject the lever stop at 40-45 from the starting position the fuel supply from all nozzles at all speeds cam shaft and at any position, "aha control knob must be completely shut down. With the appropriate maximum torque speed feed willow and an air pressure P = 0,8-5-1 MPa cyclic test the supply of fuel to re-clipping. Adjusting the stroke of the corrector spend the castellated nut cor-ora. Tightening torque spring corrector is limited to the inner nut straight khorektora. Adjustments in antikorrektora According to the tabulated data make changes preload springs back corrector nut and bolt of the restriction of his

8 Aspects For Successful Operation Of Your Auto

Published by:

It's no secret that car, along with complex mechanisms has some wear and tear and neglect of this may be expensive for both sides. Of course your car from wear and tear drugs not yet invented but to minimize the very real even. Every aspect below, has its own personality and requires strict compliance. If only to comply with these eight criteria, at least 3 times a month, already you can know exactly what you thereby significantly increase the lifetime of your steel horse. So, here we go: 1) Check the tires, as well as measure the tire pressure when cold. If you do not know what should be the normal pressure in the tires, then this you can get information on the cover of the fuel tank or in the manual. 2) Make sure the work of all external lighting fixtures, namely, near and far light, brake light, turn signal, the signal of reversing alarms and marker lights. 3) Check operation of windscreen wipers and windshield.

If there is a need, then top up the liquid in the tank washer. 4) Check the motor for damaged, loose or disconnect wires and the state of radiator hose and heater, fuel lines and connections associated with hydrostrengthening steering in the presence and brakes. Attach details. 5) Check the oil level in the crankcase – namely, on a horizontal surface with the engine off, remove the dipstick and wipe with a cloth, which is not lint-free cloth. Dip the probe into the hole, then remove it all completely and make sure that the oil level is between the two marks at the top of the probe, indicating that normal.

If there is a need, then top up oil. 6) Make sure that the brake master cylinder reservoir is full. Lowering of the brake fluid reservoir indicates tightness of the hydraulic brake actuator, which can directly lead to failure of brake system. 7) The level of liquid (coolant) in the expansion tank should be between the top and bottom mark. Remember that when the engine, especially in hot weather, the amount of cooling fluid increases and it should not leak and breakfast expansion tank. 8) Finally, the backlash steering equipment shall not exceed 10 degrees. So, dear readers, you have familiarized with the main theses of (rules) to care for car. I will forgive you observe them, because this may depend not only on the serviceability of the car, but also human lives.